Workout timing · Tabata

Tabata Timer: Understand 20/10 × 8

For the 20/10 example in Timer Plus, set eight 20-second work periods with 10-second rests between them. The last work period ends the block at 3:50; preparation and breaks between blocks add time separately.

Set up eight 20/10 work periods

The developer confirms there is no rest after the last interval. These are timing values, not verified current screen labels or an intensity recommendation.

Setting or phaseExample value
Work20 seconds
Rest10 seconds between work periods
Work periods8
FinishAfter work period 8: 3:50 total
Final restNone; the separate 4:00 written example below includes another 10 seconds

Does your block end at 3:50 or 4:00?

Eight 20-second work periods add up to 160 seconds, or 2:40 of work.

Add seven 10-second rests between them: (8 × 20) + (7 × 10) = 230 seconds, or 3:50. The block finishes as work period eight ends.

Include recovery after every work period: (8 × 20) + (8 × 10) = 240 seconds, or 4:00. This version ends after the final 10-second rest.

Use the ending specified in your workout plan. Preparation, warm-up, cool-down and any break after the block add time separately.

Count an extra break between blocks

Illustrative arithmetic: assume a written plan already specifies two complete 4:00 blocks and an additional 1:00 break. Each block includes its final 10-second recovery. Preparation and other phases are outside this example.

Scroll sideways to see all columns

PartTime includedElapsed at its end
First complete block240 seconds, including the final recovery4:00
Additional break between blocks60 seconds beyond the recovery already counted5:00
Second complete block240 seconds, including the final recovery9:00 total: 240 + 60 + 240 = 540 seconds

See where each version finishes

A 20/10 pattern, repeated eight timesEight work periods of twenty seconds. Seven ten-second rests give 230 seconds in total; including the final ten-second rest gives 240 seconds.20 s WORK10 s RESTROUND 1 20 s 10 sROUND 2 20 s 10 sROUND 3 20 s 10 sROUND 4 20 s 10 sROUND 5 20 s 10 sROUND 6 20 s 10 sROUND 7 20 s 10 sROUND 8 20 s 10* * Last rest changes the total.

230 seconds without the final rest. 240 seconds with it.

  • 8 × 20 s work + 7 × 10 s rest = 230 s.
  • 8 × 20 s work + 8 × 10 s rest = 240 s.

Timing arithmetic only, not a training prescription. The Timer Plus team confirms no rest after the last interval: 20/10 with eight work intervals totals 3:50 before preparation. The dashed final rest illustrates the separate 4:00 calculation.

20 seconds of work × 8. Seven 10-second rests give 3:50; adding the eighth rest gives 4:00. Preparation and other phases are separate.

The timer pattern and the original study

The 1996 study by Tabata and colleagues examined a specific cycling protocol with seven to eight 20-second bouts and 10-second rests. Exercise and intensity were part of the experiment.

The familiar 20/10 timer pattern describes a schedule. Matching those seconds with another exercise does not reproduce the full research protocol or establish the same fitness outcomes.

Sources: Tabata et al. (1996) · PMID 8897392 · Abstract

The original protocol, in the authors’ words

From the research

“seven to eight sets of 20-s exercise”

I. Tabata and colleaguesOriginal cycling-study abstract · 1996Read the original source

The abstract describes a small cycling experiment with 20-second work periods and 10-second rests. The timer pattern alone does not reproduce the full study protocol.

Keep the chosen ending when setting the timer

Follow all eight work periods

  1. Choose the final phase

    Mark whether your plan stops after work period eight or includes one more 10-second recovery.

  2. Match the sequence to the controls

    Compare the controls in your installed timer with 20-second work, 10-second recovery and eight work periods. Check what its repeat count includes.

  3. Observe the finish

    During a timing-only run, count all eight work periods and watch the last transition. Compare the elapsed time with 230 or 240 seconds, plus any additional phases.

  4. Listen to phase and ending cues

    Note the cue at a phase change and the cue at the end separately. Repeat with the music and screen state you intend to use.

Explore Timer Plus

Open the listing for your device to review the current app details.