Workout timing · Run–walk
Run-Walk Interval Timer Guide
Use Timer Plus custom durations to reproduce the run and walk phases in a plan you already follow. In the work/rest example below, four 1-minute runs and three 2-minute walking rests finish at 10:00 after the last run.
Set up the run–walk work/rest example
Here running is the work phase and walking is the rest phase. Timer Plus omits the final rest. A written plan with a fourth walk totals 12:00 instead; the explanation below distinguishes those endings.
| Setting or phase | Example value |
|---|---|
| Run / work | 1 minute per run |
| Walk / rest | 2 minutes between runs |
| Run periods | 4 |
| Finish | After run 4: 10:00 total |
| If your plan includes a final walk | Keep that phase explicit in the written sequence; it is outside this 10:00 work/rest example |
Enter the durations and counts with the Timer Plus setup steps
See why this example has this ending in the detailed sequence and calculation
Twelve minutes with every walk, ten without the last
Four one-minute runs supply four minutes. Four two-minute walks supply eight: 4 × (1 + 2) = 12 minutes when every walk is included.
Omitting only the final two-minute walk leaves four runs and three walks: (4 × 1) + (3 × 2) = 10 minutes. The ending changes; the earlier pairs stay the same.
With every walk included, the pairs end at 3:00, 6:00, 9:00 and 12:00. Write preparation, warm-up and cool-down separately because they add time outside this block.
Follow four pairs of one minute, then two
1-minute run + 2-minute walk, repeated four times = 12 minutes.
- Include every walk: 4 × (1 min + 2 min) = 12 min.
- Omit only the last walk: 12 min − 2 min = 10 min.
The dashed final walk makes the alternative ending visible. This is an arithmetic example, not a suggested training plan or medical advice. It does not establish Timer Plus modes or behavior.
Arithmetic example only: 1-minute run + 2-minute walk, repeated four times, totals 12 minutes when the last walk is included. It is not a suggested training plan.
Map your plan into alternating phases
Write run and walk durations in order, then repeat that pair the number of times in your existing plan. Mark whether the last pair includes its walk or ends after the run.
The clock describes those phase changes. Pace, route and training load are separate parts of a plan; the timing example does not select them.
Compare this structure with other workout timing patterns
Read changing durations in order
A separate arithmetic example: a 1:00/2:00 pair followed by a 2:00/1:00 pair. These are illustrative durations, not a running plan. Each pair totals 3:00, but their phase lengths differ.
Scroll sideways to see all columns
| Phase | Example duration | Elapsed at its end |
|---|---|---|
| First run | 1:00 | 1:00 |
| First walk | 2:00 | 3:00 |
| Second run | 2:00 | 5:00 |
| Second walk | 1:00 | 6:00 total: 60 + 120 + 120 + 60 = 360 seconds |
A phase change, elapsed time and pace answer different questions
Read the existing 12-minute example at 4:30, counting from the first run. Preparation is outside this clock.
| Question | What the example can tell you |
|---|---|
| When do I switch? | At 4:30 you are in the second walk. The next run starts at 6:00, so 1:30 remains before the change. |
| How long have I been going? | The block has been running for four minutes and 30 seconds. That elapsed time is different from the time remaining in the current phase. |
| What is my pace? | Pace describes time per distance, such as minutes per mile. This schedule has no distance measurement, so it cannot calculate your pace. A signal to switch does not answer that question. |
Choose the information your plan calls for
In an exploratory study, three of the paper’s authors recorded their own information needs in 141 videos across 18 runs. Needs included elapsed time, speed and pace planning; only 11 needs were shared by all three runners. The study collected questions, rather than testing whether a particular display improved running.
For a run–walk sequence, identify the current phase and the next change. If your existing plan also calls for pace or distance, list that as a separate information need when checking a device. Do not assume a time cue supplies it.
Sources: Elshabasi et al. (2024) · arXiv:2409.06426v1 · PDF p. 2
If you plan to use a watch, compare these needs with the Apple Watch device questions
Choose the information you need
From the research
“not all data will be relevant all the time.”
Elshabasi and colleagues explored information needs through 18 runs by three author-participants. For your own plan, distinguish a phase-change cue, elapsed time and pace. This preliminary study did not evaluate Timer Plus or a run–walk program.
Check the ending and cues in the version you use
Follow the alternation before taking it outside
Use the plan’s actual durations
Record its run time, walk time, pair count and final phase. The illustration supplies arithmetic, not replacement durations for your plan.
Match the complete sequence
Compare both phase lengths and the repeat count with the controls in your installed timer.
Observe the transitions
Perform a timing-only run. Count each run, walk and pair, then compare the final phase and total with your notes.
Repeat with the intended device setup
Keep the screen state and audio output you will use with that result. If either changes, make a separate comparison.
Explore Timer Plus
Open the listing for your device to review the current app details.
For the Apple listing and device checks, read the iPhone and iPad listing guide
For the Google Play listing and device checks, read the Android listing guide