Workout timing · EMOM

EMOM Timer Guide: Read the Minute Cues

EMOM means every minute on the minute: each minute boundary marks a new start. In this six-minute example, work starts at 0:00 through 5:00, and the block finishes at 6:00. Work inside each minute comes from your existing plan.

Six starts, then the finish at 6:00

The six starts fall at 0:00, 1:00, 2:00, 3:00, 4:00 and 5:00. Each opens one minute of the block. The 6:00 boundary ends the sixth minute; it does not add a seventh start.

For any positive whole number n of minutes, there are n starts: from 0:00 through minute n − 1, with the finish at minute n. A 10-minute block therefore has its last start at 9:00 and ends at 10:00.

After the planned task is complete, any time left belongs to that same minute. Put each task beside its minute on paper if your plan alternates them. Preparation happens before 0:00 and adds to the overall elapsed time.

Read the six-minute sequence

A six-minute EMOM structureSix minute blocks start at 0:00, 1:00, 2:00, 3:00, 4:00 and 5:00. The block finishes at 6:00. After the work in each minute is completed, that minute’s remaining time is rest. No work duration is specified.START 0:00 WORK RESTSTART 1:00 WORK RESTSTART 2:00 WORK RESTSTART 3:00 WORK RESTSTART 4:00 WORK RESTSTART 5:00 WORK RESTFINISH 6:00 Rest = time left in that minute

Six starts, one minute apart. Finish at 6:00.

  • Start times: 0:00, 1:00, 2:00, 3:00, 4:00 and 5:00.
  • Each minute contains its work and any remaining rest.

EMOM means “every minute on the minute.” These six blocks illustrate that structure. Bar heights do not represent durations; exercise, repetitions, effort and app support are not specified.

Illustration only: starts at 0:00, 1:00, 2:00, 3:00, 4:00 and 5:00; the six-minute block ends at 6:00. Exercise, repetitions and effort are not specified.

An EMOM user’s perspective

App Store review · iOS

“it really helps you stay on track.”

Lapidarian · US App Store · review excerptRead the review in the App Store

The reviewer describes kettlebell and EMOM use, and also reports limits when editing saved timers and varying round lengths. Read the full review for those qualifications.

A minute cue is different from a fixed 30/30 split

In a simple EMOM schedule, starts stay one minute apart while the time spent on the task can vary. The clock marks the boundary, not a required work duration or repetition count.

A fixed 30-second work phase followed by 30 seconds of recovery divides each minute at the same point. That is a different timing instruction from completing the planned task and using whatever remains before the next minute.

Calculate what remains in the minute

For a clock-only example, take a minute that starts at 2:00. If the task finishes at 2:25, there are 35 seconds left before the next start at 3:00: 60 − 25 = 35.

The 25 seconds illustrate the calculation; they are not a target completion time. The minute boundary stays at 3:00 rather than moving to 3:25.

Match the minute cues before using the setup

Follow the starts and the ending separately

  1. Write the minute plan

    Record the number of minutes, each task and any preparation before the first start.

  2. Match the boundaries to the controls

    Compare the required sequence with your installed timer’s controls and repeat-count convention.

  3. Run the clock check

    Observe a timing-only run against an independent clock. Count the starts separately from the ending cue.

  4. Listen with your intended setup

    Repeat with the music, audio output and screen state you intend to use.

Explore Timer Plus

Open the listing for your device to review the current app details.